LEDMatrix/docs/SSH_UNAVAILABLE_AFTER_INSTALL.md

SSH Unavailable After Installation - Troubleshooting Guide

Why SSH Becomes Unavailable

After running first_time_install.sh, SSH may become unavailable for the following reasons:

1. WiFi Monitor Service Enables AP Mode

Primary Cause: The WiFi monitor service (ledmatrix-wifi-monitor) automatically enables Access Point (AP) mode when it detects that the Raspberry Pi is not connected to WiFi. When AP mode is active:

• The Pi creates its own WiFi network: LEDMatrix-Setup (password: ledmatrix123)
• The Pi's WiFi interface (wlan0) switches from client mode to AP mode
• This disconnects the Pi from your original WiFi network
• SSH becomes unavailable because the Pi is no longer on your network

2. Network Configuration Changes

The installation script:

• Installs and configures hostapd (Access Point daemon)
• Installs and configures dnsmasq (DHCP server for AP mode)
• These services can interfere with normal WiFi client mode

3. The Board Ran Out of Memory

On a 512MB or 1GB board, memory exhaustion stops sshd being able to fork a session process. The connection is accepted and then closed immediately, before any banner:

kex_exchange_identification: Connection closed by remote host

The giveaway is that the board is otherwise healthy — ping is clean and the web UI still responds — but nothing that needs to start a new process works, and the panel is usually dark. Only a power cycle clears it. See LOW_MEMORY_BOARDS.md.

4. Reboot After Installation

If the script reboots the Pi (which it recommends), network services may restart in a different state, potentially triggering AP mode.

How to Regain SSH Access

Option 1: Connect to AP Mode (Recommended for Initial Setup)

1. Find the AP Network:

   • Look for a WiFi network named LEDMatrix-Setup on your phone/computer
   • Default password: ledmatrix123

2. Connect to the AP:

   • Connect your device to the LEDMatrix-Setup network
   • The Pi will have IP address: 192.168.4.1

3. SSH via AP Mode:

   ssh devpi@192.168.4.1
   

4. Disable AP Mode and Reconnect to WiFi: Once connected via SSH:

   # Check WiFi status
   nmcli device status
   
   # Disable AP mode manually
   sudo systemctl stop hostapd
   sudo systemctl stop dnsmasq
   
   # Connect to your WiFi network (replace with your SSID and password)
   sudo nmcli device wifi connect "YourWiFiSSID" password "YourPassword"
   
   # Or use the web interface at http://192.168.4.1:5000
   # Navigate to WiFi tab and connect to your network
   

Option 2: Disable WiFi Monitor Service Temporarily

If you have physical access to the Pi or can connect via AP mode:

# Stop the WiFi monitor service
sudo systemctl stop ledmatrix-wifi-monitor

# Disable it from starting on boot (optional)
sudo systemctl disable ledmatrix-wifi-monitor

# Stop AP mode services
sudo systemctl stop hostapd
sudo systemctl stop dnsmasq

# Reconnect to your WiFi network
sudo nmcli device wifi connect "YourWiFiSSID" password "YourPassword"

Option 3: Use Ethernet Connection

If your Pi is connected via Ethernet:

• SSH should remain available via Ethernet even if WiFi is in AP mode
• Connect via: ssh devpi@<pi-ip-address>

Option 4: Physical Access

If you have physical access to the Pi:

1. Connect a keyboard and monitor
2. Log in locally
3. Follow Option 2 to disable AP mode and reconnect to WiFi

Preventing SSH Loss in the Future

Method 1: Configure WiFi Before Installation

Before running first_time_install.sh, ensure WiFi is properly configured and connected:

# Check WiFi status
nmcli device status

# If not connected, connect to WiFi
sudo nmcli device wifi connect "YourWiFiSSID" password "YourPassword"

# Verify connection
ping -c 3 8.8.8.8

Method 2: Disable WiFi Monitor Service

If you don't need the WiFi setup feature:

# After installation, disable the WiFi monitor service
sudo systemctl stop ledmatrix-wifi-monitor
sudo systemctl disable ledmatrix-wifi-monitor

Method 3: Configure WiFi Monitor to Not Auto-Enable AP

Edit the WiFi monitor configuration to prevent automatic AP mode:

# Edit the WiFi config (if it exists)
nano /home/devpi/LEDMatrix/config/wifi_config.json

# Or modify the WiFi monitor daemon behavior
# (requires code changes to wifi_monitor_daemon.py)

Verification Steps

After regaining SSH access, verify your installation:

cd /home/devpi/LEDMatrix
./scripts/verify_installation.sh

This script will check:

• Systemd services status
• Python dependencies
• Configuration files
• File permissions
• Web interface availability
• Network connectivity

Quick Reference Commands

# Check WiFi status
nmcli device status
nmcli device wifi list

# Check AP mode status
sudo systemctl status hostapd
sudo systemctl status dnsmasq

# Check WiFi monitor service
sudo systemctl status ledmatrix-wifi-monitor

# View WiFi monitor logs
sudo journalctl -u ledmatrix-wifi-monitor -f

# Connect to WiFi
sudo nmcli device wifi connect "SSID" password "password"

# Disable AP mode
sudo systemctl stop hostapd dnsmasq

# Restart network services
sudo systemctl restart NetworkManager

Web Interface Access

Even if SSH is unavailable, you can access the web interface:

1. Via AP Mode: Connect to LEDMatrix-Setup network and visit http://192.168.4.1:5000
2. Via WiFi: If WiFi is connected, visit http://<pi-ip-address>:5000
3. Via Ethernet: Visit http://<pi-ip-address>:5000

The web interface allows you to:

• Configure WiFi connections
• Enable/disable AP mode
• Check service status
• View logs
• Manage the LED Matrix display

Summary

SSH becomes unavailable because:

• WiFi monitor service enables AP mode when WiFi disconnects
• AP mode switches WiFi from client to access point mode
• Pi loses connection to your original network

To regain SSH:

1. Connect to LEDMatrix-Setup AP network (password: ledmatrix123)
2. SSH to 192.168.4.1
3. Disable AP mode and reconnect to your WiFi network
4. Or disable the WiFi monitor service if not needed

To prevent future issues:

• Ensure WiFi is connected before installation
• Or disable WiFi monitor service if you don't need AP mode feature